Mastic white smooth matching slatted tombstone vent.
Bringing in a gable wall for real curb appeal can sometimes be a headache.
Why even try to dress up the gable wall instead of leaving it blank?
Should I gable vent or not?
Curb appeal of a home can drastically change the mindset of any homeowner.
If the home exterior is pleasing, then occupants will be happier to go home.
By simply changing a gable vent from a rectangle to a tombstone can help take eyes away from a boxy style home's bland appearance.
Obtain
Tombstone aerated exhaust vents
Ordering a tombstone vent is easy.
Just know the width and center height.
Why do we ask for the side leg height?
This is what tells us the arch curvature.
If the vent opening isn't cut yet, then a true half circle arch is fine.
But a lot of tombstones are short on the arch.
This picture of this tombstone vent just happens to be a true half round.
These vents are made as one complete unit to keep the slats in line and spaced evenly.
Why use a front flange on a tombstone?
The boxed rectangular portion is simple to trim around.
But the top arch is not.
With the arch already trimmed to match the bottom, the vent is complete after install and does not need additional trimming.
This vent depth is only 1 inch so it can fit in tight areas where wall framing may be in the way or cannot be cut out.
Wall support studs should never be removed without rebracing the wall to install an attic vent.
What type of screening should be used on the attic vent?
This customer specified there were problems with squirrels, bats and roof rats in the neighborhood.
Bats can be detered by using a thinner vent such as the 1 inch deep.
There isn't enough space under the louvers for the bats to nest comfortably.
The aluminum screen seen here keeps out bugs such as wasps.
But for the squirrels and roof rats, the 1/2 inch wire mesh is added.
This does not block any air flow but does block most all birds and 4 legged creatures.
Obtain 14 X 22 X 1 Tombstone vent in this huge selection of 14 x 22 aerated exhaust vents with a front flange and a 1 inch depth
Tombstone aerated exhaust vent is just a squared and an arch top. These vent tops often catches all of the distraction. Measures the Tombstone vent is much quicker than you might have thought. Just forget the top and set your mind to the rectangulared base of it. The horizontal measure, the side measure and the total height are the only 3 measurements required to purchase one of these 14 x 22 tombstone front flange vents and know it will apply nicely.
A personalized aluminum louvre working vent with personality.
Pearl River Louisiana 70452 now has another attic protected by these vents
Just know the width and center height.
Why do we ask for the side leg height?
This is what tells us the arch curvature.
If the vent opening isn't cut yet, then a true half circle arch is fine.
But a lot of tombstones are short on the arch.
This picture of this tombstone vent just happens to be a true half round.
These vents are made as one complete unit to keep the slats in line and spaced evenly.
Why use a front flange on a tombstone?
The boxed rectangular portion is simple to trim around.
But the top arch is not.
With the arch already trimmed to match the bottom, the vent is complete after install and does not need additional trimming.
This vent depth is only 1 inch so it can fit in tight areas where wall framing may be in the way or cannot be cut out.
Wall support studs should never be removed without rebracing the wall to install an attic vent.
What type of screening should be used on the attic vent?
This customer specified there were problems with squirrels, bats and roof rats in the neighborhood.
Bats can be detered by using a thinner vent such as the 1 inch deep.
There isn't enough space under the louvers for the bats to nest comfortably.
The aluminum screen seen here keeps out bugs such as wasps.
But for the squirrels and roof rats, the 1/2 inch wire mesh is added.
This does not block any air flow but does block most all birds and 4 legged creatures.
Stronger Rounded Top Gable Side Vent
| Vent Size | receive | receive | apx | |||
| if you choose... | order width | order height | vent width | vent height | net free | |
| opening size | 14 | 22 | 13.5 | 21.5 | 106 | |
| tip to tip of vent | 14 | 22 | 14 | 22 | 114 | |
| tip to tip including flange | 14 | 22 | 11 | 19 | 72 |
Depth: 1 inch deep
Color Coating: All Aluminum Trim Coil
Nail Fin: Front Flange
Constructed Of: .019 Aluminum Sheet Metal
Functional: Aluminum, Solid aluminum back, Vinyl screening, Aluminum screening
14x22x1tslvffss
A personalized aluminum louvre working vent with personality.
Pearl River Louisiana 70452 now has another attic protected by these vents
What else?
901.281.2887 contactus@onyxxteriors.com